Faux Marble Countertop Using Epoxy Resin

I received epoxy resin as a gift about a year in the past and ultimately got round to using it on my bathroom countertop. I changed into planning to update my sink and faucet besides, so notion this will be an awesome time to tackle the countertop too.

faux marble countertop using epoxy resin
faux marble countertop using epoxy resin

After getting rid of the sink and tap I gave the countertop an excellent cleaning with TSP degreaser and taped off the rims with painter’s tape. 

I taped plastic to the bottom of the sink beginning with duct tape. This fell off three times earlier than I even started out working on it! So I used push pins to preserve it in place. Those held up properly!

faux marble countertop using epoxy resin
faux marble countertop using epoxy resin

I then painted the countertop (and arrogance) with white primer – 2 coats. 

Once it became dry I taped plastic to the cabinet and flooring. I used overlaying tape and it held up first-class.

faux marble countertop using epoxy resin
faux marble countertop using epoxy resin

Prior to beginning, I made sure the house temperature changed into as much as 80 tiers and I sat each packing containers of epoxy in a bowl of warm water for a couple of minutes, as in line with the ProMarine instructions.  
 
Then I blended ¾ of the epoxy resin (half of and half of aggregate). Once blended I separated a small quantity into a plastic cup to feature black for the marble veins.

I blended a small quantity of white unicorn spit into the last resin and poured it onto the countertop and smoothed it out with a small foam curler. I used a broom to use it to the backsplash.

Once it appeared fully blanketed, I used the brink of a stir persist with create black veins in the white, seeking to make it seem like marble.
I then feathered out the black strains the use of a sea sponge and a warmth gun. I also went over it speedy with a torch to pop bubbles occasionally.

I took place to glance down and saw that the black tinted epoxy had erupted over the cup and turned into smoking!!! Fortunately I had an empty box nearby, so I located the smoking cup in the box and taken it outside. It cooled off quickly and stopped smoking!

The next time I use epoxy, I received’t blend my accessory colour with it. I’ll just use the paint as it’s far. It could have settled into the epoxy anyway.
GAMBAR3 The countertop now had a lovely glossy end!  
But I wasn’t loving how the veins looked at the backsplash. And close up the backsplash had little run strains that wouldn’t smooth out. And I felt like perhaps I used too much black over all. So I had the concept that I could blend the last epoxy with white and pour it on, to optimistically fill within the runs and tone down the veins. 

So after waiting 4 hours (as in line with the directions) I added white greenback save paint (I didn’t have any greater unicorn spit) to the epoxy and poured it immediately onto the backsplash and allow it run down. Then used a sponge roller to easy it out over the surface. 

Unfortunately, I used an excessive amount of white paint and it made everything look a bit milky. I scraped as a lot off as viable with a plastic trowel, however it nonetheless took away a LOT of the sleek finish that were there. 

The next time I use epoxy on a countertop (I plan to do my daughters as nicely) I will no longer use epoxy on the backsplash. I’ll just paint it the equal base color and seal it with a sleek polyurethane.

I additionally received’t stop operating on it until I’m happy with the final results. No 2nd pour! You truly have numerous time to work with it. Even although I nonetheless truely just like the way it became out ultimately, I am a bit disillusioned I ruined the excessive gloss.
The next day I eliminated the painter’s tape. I should not have waited that lengthy! Some of it was dried on beneath the epoxy. I used an exacto knife to get off as plenty as I could.
After it become absolutely cured (3 days) I just added a bead of caulking to hide the remnants of inexperienced tape.

I gave the epoxy a mild sanding and set up my new sink and tap.
Even although I will do some things otherwise subsequent time, I virtually do just like the outcome. The countertop honestly looks like actual marble! I’m satisfied I sooner or later got around to doing it. It really brightened up my ensuite! And I’m looking forward to attempting this once more.

Faux Marble Countertop Using Epoxy Resin Uploaded by admin on Monday, November 18th, 2019. We have 3 great pictures of Faux Marble Countertop Using Epoxy Resin. Find DIY Globalnet on category Repairing.

See also from Repairing Topic.

Here we have 3 great photos about Faux Marble Countertop Using Epoxy Resin. We hope you enjoyed it and if you want to download the pictures in high quality, simply just click the image and you will be redirected to the download page of Faux Marble Countertop Using Epoxy Resin.

Related Post to Faux Marble Countertop Using Epoxy Resin

Leave a Reply

Your email address will not be published. Required fields are marked *