DIY Fireplace Surround

If you war each yr with finding somewhere to grasp the stockings, then this could simply be the diy you need this winter! It will without problems deliver over into each season and made this sort of difference to my space.

This diy does require using numerous power tools, so that you do need to be at ease with the usage of or have someone on hand to help. If you already have the paint and energy gear then this diy will simplest cost $60! A extraordinary saving while comparing to the rate of save sold surrounds which begin at around $2 hundred

diy fireplace surround
diy fireplace surround

diy fireplace surround
diy fireplace surround

You’re going to want:
1x8x6 boards (3)
1x3x8 board
1x12x4 stair tread (with the rounded the front edge)
decorative trim (elective)
11/2 inch screws
4×8 backerboard
nail gun
chop saw
sander
drill
Wood glue
spackling
Paintable caulk

diy fireplace surround
diy fireplace surround

First, you’re going to apply your chop noticed to cut all your three 1x8x6 forums in half of, ensuing in 6 pieces which are 3ft every. Then using some wood glue to assist preserve them, drill pilot holes and screw boards at the lower back of 1 board to provide you three sides, forming the columns. I used a screw on the pinnacle and backside on every side because I knew my trim might hide the screws. If you don’t need to have trim, then you can use a pocket hollow jig to hide all screws interior.

diy fireplace surround
diy fireplace surround

You’ll become with this, and can discover that if your timber wasn’t flawlessly straight then there’s a few bowing, however no longer an trouble! You can cut a bit off your 1x3x8 for a aid at the returned aspect like I did below.

diy fireplace surround
diy fireplace surround

You can drill pilot holes and screw into each facet as again the trim will cover the screws, even though I located that the nail gun was sufficient right here, and tacked them into the aspect portions.

diy fireplace surround
diy fireplace surround

Next, cut your 1x3x8 into 6 pieces measuring as you go. 4 portions for the perimeters, and longer portions for the the front. I should have 45 diploma angled these, however desired to keep it easy. The manner I have executed it makes the front best and seamless. Nail gun these portions on on your columns.

diy fireplace surround
diy fireplace surround
diy fireplace surround
diy fireplace surround

I used a Stanley knife to score the backerboard to the right top as it was a bit tall, then it’s going to bend off quite simply. I also connected this to the again of the columns with the nail gun. Thinking ahead. If you’re going to have a small plug in heater in the surround, go away it just a few millimetres short on the lowest so the cord can take a seat underneath.

diy fireplace surround
diy fireplace surround

Next up, flip your chop saw to a 45 diploma slicing perspective and cut your decorative trim in order that it meets properly on every side. I sold sufficient trim to trim the top and across the legs at the lowest, but handiest ended up doing the pinnacle as I preferred it greater minimalist so I’d recommend sketching out how you want it to look and how fancy you want to go along with info.

diy fireplace surround
diy fireplace surround
diy fireplace surround
diy fireplace surround

0 I used some wood glue across the pinnacle for additonal power, then placed the stair tread onto the complete piece ensuring it’s concentrated. Then I pilot holed and sank 4 screws into the top, two on the returned and at the the front. It’s crucial to sink them so that you can fill the holes to cause them to smooth earlier than portray.

diy fireplace surround
diy fireplace surround

1 Then use your filler (wood filler or spackle, I simply choose spackle because it’s a positive that the paint received’t affect it), and cover the ones holes. You will even need to cover the holes from the nail gun.

diy fireplace surround
diy fireplace surround

2 Next take your paintable caulk and use it to caulk all of the joints and seams at the piece.

diy fireplace surround
diy fireplace surround

3 Once your filler and caulk have fully dried you may give the wooden a light sand, earlier than the usage of a tack cloth to get all of the dust off equipped for paint. I decided to test out my paint sprayer for this piece so I plastic included a place to do so, however a good high-quality brush and paint will by no means permit you to down!

diy fireplace surround
diy fireplace surround

4 As usually, please ask away when you have any questions and maintain up with me on Instagram @where_the_winds_blow for different crafts and decor!

DIY Fireplace Surround Uploaded by Grace Blaxland on Saturday, January 4th, 2020. We have 14 great pictures of DIY Fireplace Surround. Find DIY Globalnet on category Plumbing.

See also from Plumbing Topic.

Here we have 14 great photos about DIY Fireplace Surround. We hope you enjoyed it and if you want to download the pictures in high quality, simply just click the image and you will be redirected to the download page of DIY Fireplace Surround.

Related Post to DIY Fireplace Surround

Leave a Reply

Your email address will not be published. Required fields are marked *